MIKE 11 GIS
Release Note - 2011
Welcome to MIKE 11 GIS Release 2011.
MIKE 11 GIS is a pre- and postprocessing module for MIKE 11. As an extension to ESRI ArcMAP™ 10.0 version and requires that ArcGIS is pre-installed. It assist setting up network, cross-sectional and boundary files for MIKE 11 models, and can be used to present time series results and flood maps from MIKE 11 simulations. It also includes non-point and point pollutant load estimation tools for MIKE 11 WQ simulations. A comprehensive time series data managment capability is included.
The recommended minimum hardware requirements are:
| Supported Operating Systems: | Windows XP Professional (32 and 64 bit), Windows Vista Business (32 and 64 bit), Windows 7 Professional (32 and 64 bit) |
| Processor: | 2.0 GHz PC (or higher) |
| Memory (RAM): | 1GB (or higher) |
| Hard disk: | 40 GB (or higher) |
| Monitor: | SVGA, resolution 1024x768 in 16bit colour |
| Graphic Card: | 32 MB RAM (or higher), 24 bit true colour |
| Media: | CD-ROM/DVD drive, 20 x speed (or higher) |
| File system: | NTFS |
Installation^ top
To install MIKE 11 GIS, please choose 'MIKE 11 GIS in the 'MIKE BY DHI' dialog that appears when inserting the MIKE software 2011 DVD and then press the 'Install' button.
The setup program automatically installs all necessary MIKE 11 GIS files and folders on your PC.
License File and Dongle^ top
To use MIKE 11 GIS in licensed-mode please follow these steps:
- Make sure that the provided dongle is attached to the computer (parallel or USB port - for Windows XP Professional x64 Edition USB port only)
- The dongle driver is installed automatically during the setup of the program
- The MIKE software license file (DhiLicense.dat) may be retrieved using the Internet. An Internet connection and a valid e-mail address are required. The license file may be retrieved in two ways:
- During installation of MIKE Software
- After installation of MIKE Software, by launching the License Updater through the start menu
- To retrieve your license file during installation of MIKE Software, select “Local” when prompted to select the type of License Management, and then select “Internet” and follow the on-screen instructions
- To update your license file using the License Updater, simply launch “Start->Programs->MIKE BY DHI 2011->License Updater” and follow the on-screen instructions.
- Alternatively, the license file can simply be copied from the supply medium (attachment to e-mail from DHI or CD/DVD) in \Program Files\DHI\2011\License or Program Files (x86)\DHI\2011\License.
Product Invocation^ top
To start MIKE 11 GIS, go to Start -> Programs -> MIKE BY DHI 2011 -> MIKE GIS and select 'MIKE GIS'.
MIKE 11GIS cannot be started without a configured Software Key and valid license file for MIKE 11 GIS. Please contact DHI's Software Support Center.
If the MIKE 11 GIS toolbas does not appear when starting up MIKE 11 GIS, the following steps may be taken:
Enabling MIKE 11 GIS for ArcGIS Extension
The MIKE 11 GIS extension may need to be enabled as follows:
- Select Tools from ArcMap™ menu bar
- Point to Extensions
- Check 'MIKE 11 GIS' and from the list of extensions and click Close button.
MIKE 11 GIS toolbar
To turn on visibility of MIKE 11 GIS toolbars, proceed as follows
- Select View from ArcMap™ menu bar
- Point to Toolbars
- Make sure 'MIKE 11 GIS' has a box checked. If not then check the box and click on the Close button.
Support^ top
The Software Support Center can be reached by mail, e-mail, phone or fax:
Software Support Center
DHI
Agern Allé 5
DK-2970 Hørsholm
Denmark
mikebydhi@dhigroup.com
Tel: +45 4516 9333 (Open 7.30-16.00 GMT)
Fax: +45 4516 9292
New features^ top
Known Defects & Workarounds^ top
MIKE 11 GIS Service Pack 1, February 2011^ top
MIKE 11 GIS Service Pack 2, February 2011^ top
No changes have been made for MIKE 11 GIS in Service Packs 1 and 2
MIKE 11 GIS Service Pack 3, April 2011^ top
| Module/Type | Error/Inconvenience/New Feature | Status |
Remarks |
| File Import | Import of Cross section file including closed
cross sections failed. |
Fixed |
|
| File Export | Export of Cross sections to XNS11-file causing
ArcGIS to crash. |
Fixed | |
| File Export | Export to River Network to NWK11-file caused ArcGIS to crash. |
Fixed |
MIKE 11 GIS Service Pack 4, June 2011^ top
No changes have been made for MIKE 11 GIS in this Service Pack
MIKE 11 GIS Service Pack 5, June 2011^ top
No changes have been made for MIKE 11 GIS in this Service Pack
MIKE 11 GIS Service Pack 6, October 2011^ top
| Module/Type | Error/Inconvenience/New Feature | Status |
Remarks |
| File Import | Import of multiple Cross sections from point
shapefile occasionally caused the cross section file to be
corrupt when re-opening the MIKE 11 GIS project. Following this,
all cross section information was lost. |
Fixed |
|
| File Export | Export of River Network to NWK11-file: The
Nwk11-file was not saved in the correct format for MIKE 11
release 2011. |
Fixed |
MIKE 11 GIS Service Pack 7, January 2012^ top
No changes have been made for MIKE 11 GIS in this Service Pack